download the last version for ios Wirecast Pro

Download the last version for ios Wirecast Pro for free#
Download the last version for ios Wirecast Pro how to#
Download the last version for ios Wirecast Pro install#
Download the last version for ios Wirecast Pro portable#
Download the last version for ios Wirecast Pro android#

The next step is to setup the actual script that will do the work. If you have an additional controller do the same step for that controller, in my case I do so below is my config for that controller. Once on the right side, highlight it and select your first controller from the list. In my case I have 2 controllers, if you are only using one controller the additional midi entry that you see in my config would not be needed.įirst, on the left select the midi in option and either double click it or drag it to the right. Within MidiPipe there is some setup that needs to be done. What is needed for these scripts to work is a small little program called MidiPipe.

Download the last version for ios Wirecast Pro how to#

In the next section we will walk through how to set everything up. We provide all of the scripts and TouchOSC files you need. At the time of me writing this it was $4.99.

Download the last version for ios Wirecast Pro android#

There is a version of TouchOSC for iOS and Android that you can download. midi-pipe sees that command and tells wirecast what to do.įor the mobile devices we add TouchOSC Bridge which recieves OSC commands from the TouchOSC application that runs on a mobile device. So when a key is pressed on a Korg device, it send a midi control command. A script written in applescript for midi-pipe listens for Midi commands, when it sees certain pre-defined Midi commands, it performs actions in WireCast using the AppleScript interface to Wirecast. If you are planning on using a mobile device for control too, then you will also need to download another free program called TouchOSC Bridge.īefore we get into how to set everything up, here is how it works. Again search Google for 'KORG KONTROL Editor'. The next most important piece of software is the Korg software that writes scenes to the Korg Controllers. You can search Google to find it and download it. The first you need is a free program called midi-pipe. Only 2 if you are not going to be using a mobile device like an iPad or Android device. There are 3 additional pieces of software that you will need to get this working. I may in the future have a windows version but for now, sorry it is only Mac. What You Needįirst of all, this only works on the Mac. Everything you need is available at the link above.

Download the last version for ios Wirecast Pro install#

Be sure to read the sections below on how to install and what is needed. You can download the latest scripts by going to. I have tried to document the script well so that you can play with it and make changes that fit your needs. Using the same script allows enhancements and repairs to be made across both versions of the script. If you look at the source code for the script and search for ATEM you will find comments where one line needs to be commented and another un-commented. The scripts are actually identical to each other, it takes about 5 minutes to take the latest script and adjust it to work as the other script. The hybrid version uses the ATEM to switch the video and uses Wirecast to do the graphics, lower 3rds and DDR playback. The ScriptsĪs mentioned above, there are 2 scripts, one that controls only wirecast and one that controls both wirecast and the ATEM.

Download the last version for ios Wirecast Pro for free#

I wanted to provide this project to anyone who wanted control over a wire cast system just like the scripts that I found for free on the Internet.

This page will describe the project and give you links where you can download everything for free.

You can control Wirecast on an iPhone, iPad or any Android device.

Download the last version for ios Wirecast Pro portable#

I have also created an iPad and android interface that allows you to control wire cast using a portable device. I have different versions of my scripts, one is strictly 100% wire cast and the other combines wire cast and the ATEM switch into just one interface. That provides for 15 DDR's for playback and a stop button.īecause I use black magic design ATEM for my main switcher and wire cast to provide the graphics and video playback I wanted to create scripts that would work with both devices at the same time. I use the NanoKontrol similarly to how the other scripts did and I have setup the NanoPad for DDR playback. I have rewritten the bulk of them to control wire cast with a Korg NanoKontrol and NanoPad. My scripts are based off of some pieces of the scripts I've seen on the Internet. There are scripts that allow you to use Korg NanoKontrol to control WireCast and I have tried those scripts. I have Wirecast installed and working but the user interface to Wire cast is lacking. To get around this I have been looking at using the Wirecast to perform the lower thirds and video playback. I have been using an ATEM switcher which lacks some of the nice graphic ability that I desire as well as video playback.

As you probably know from reading my website I do video podcasting. So here is a little background on this project.